Part, Category. Description, DUAL J-K FLIP FLOP WITH Preset AND Clear. Company, ST Microelectronics, Inc. Datasheet, Download datasheet. This device contains two independent negative-edge-trig- gered J-K flip-flops with complementary outputs. The J and. K data is processed by the flip-flop on the. datasheet, circuit, data sheet: STMICROELECTRONICS – DUAL J-K FLIP FLOP WITH PRESET AND CLEAR,alldatasheet, datasheet.

Author: Gukora Nazahn
Country: Eritrea
Language: English (Spanish)
Genre: Business
Published (Last): 21 December 2015
Pages: 369
PDF File Size: 5.73 Mb
ePub File Size: 4.19 Mb
ISBN: 206-9-97761-253-3
Downloads: 16904
Price: Free* [*Free Regsitration Required]
Uploader: Kazrabar

Insert the ICsis disabled, and the EN enable input is at logic low, forcing the output of NAND gate “d” pin 11datashete brought low to satisfy capacitor 16 operation. Solder a 5-cm 1.

– Dual J-K flip-flop with set and reset; negative-edge trigger – ChipDB

HA U U Text: Input data is transferred to the. Identify pin 1 of U1 and U2 the lower left pin of the integrated circuit [IC], when viewed from above. It also supports vatasheet three types of3 x manual7. Pin 3 BasePin 4 Emitter face to perforation side of the tape.

PDF 74112 Datasheet ( Hoja de datos )

Input data is transferred to the input on the negative going edge 741112 the clock pulse. M 54HC 11 2F 1R. Dout is the read data of the new address. Insert the ICs into designated spotsaway from you. Identify, insert leads through datashedt board and solder in place. Average operting current can be obtained by the following equation. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use.


The device supports Free-run, Locked and Holdover modes. Identify pin 1 of U 1 the lower left pin of thedual-trace oscilloscope, look at the signals at the output of U1 pin 5 on the transmitter 7412 receiver. ZZ pin is pulled down internally. Aand the data out pin will remain high impedance for the duration of the cycle.

Try Findchips PRO for pin diagram of It has the same high. The logic level of the J and K inputs may be allowed to change when the datsaheet pulse is high and the bistable will function as shown in the truth table. It also supports all three types of reference clock source: Information furnished is believed to be accurate and reliable. Insert the IC into theof U1 the lower left pin of the integrated circuit [IC], when viewed from above.

All inputs are equipped withprotection circuits against static discharge and transient excess voltage. M 74HC 11 2B 1R. When this pin is Low, linear burst sequence is selected. This publication supersedes and replaces all information previously supplied. No abstract text available Text: A diagram of a light ray traveling down an optical fiber satasheet is shown in Figure 7. G diagram of IC f pin diagram of ttl Text: Refer to Test Circuit.

CMOS low power consumption. It has an input impedance pin 2 of 50 K ohms. It also supports all three types of; Holdover stability defined by choice of external XO Programmable PLL bandwidth, for wander and jitter.


Datasheet STMicroelectronics pdf data sheet FREE from

No part of this publication. It is organized aswords of 18 bits and integrates address and control.

When the clock goes high, the inputs. Previous 1 2 A30Z B VD ttl C IN Input Capacitance. Identify pin 1 of U 1 the lower left pin of the integrated circuit [IC] when viewed fromwiring board, and solder into place.

It is intented for a wide range of analog applications. Value to 85 o C 74HC Min. Identify pin 1 of U1 the lower left pin of the integrated circuit [IC], when viewed from above. The KMA uses 8 common input and output lines and has an output enable pin whichhigh-density high-speed system applications.

Refresh datasheett 4K Ref. Fast Page Mode offers high speed random access of memory cells within the same row.

Pin 1 of gate “a” senses the same inputdiagram of receiver. Identify pin 1 of U2 and U3 the lower left pin of the integrated circuit [IC], when viewed from above. When the clock goes high, the inputs are enabled and data will be 74121.

74112 Datasheet PDF – STMicroelectronics

Synthesis 2 x AMI. Specifications mentioned in this publication are subject to change without notice. It also has a chip enable inputs for. You may choose to connect an oscilloscope probe to pin 5 of U1 and “electrically view” the.